?2010 tyco electronics corporation, berwyn, pa all rights reserved te logo and tyco electronics are trademarks. *trademark. other products, logos, and company names might be trademarks of their respective owners. instruction sheet tooling assistance center 1-800-722-1111 product information 1-800-522-6752 this controlled document is subject to change. for latest revision and regi onal customer service, visit our website at www.tycoelectronics.com 1 of 2 loc b figure 1 1. introduction extraction tools 91047-[ ] are designed to extract flexible flat cable (ffc) contacts from ffc pin, receptacle, and edge connectors with end entrance locking lance slots (reference part number 86670-8). read these instructions thoroughly before removing any contacts. for connectors with side entrance locking lance slots, refer to 408-7916 for tool 91200-[ ]. dimensions in this instruction sheet are in millimeters [with inches in brackets]. figures are not drawn to scale. reasons for reissue of this instruction sheet are provided in section 6, revision summary. 2. description each tool features a specific number of tool blades that release the contact locking lances of the connector. see figure 1. the number of tool blades must match the number of cavities in one row of the connector. all contact locking lances must be released simultaneously; otherwise, damage to the connector, contacts, or cable may result. 3. extraction procedure refer to figure 2, and ens ure that the number of blades of the extraction to ol matches the number of contact cavities in one row of the connector. figure 2 proceed as follows: 1. align the tool blades with the locking lance slots located between the contacts and outer edge of the housing as shown in figure 1. 2. simultaneously insert all tool blades straight into the connector until the tool bottoms. only the radius between the tool bl ades should be visible when the tool is properly seated. see figure 3. 3. holding the tool and connector in one hand, carefully pull on the cable. a slight side-to-side motion may be used to ease contact extraction. note i caution ! extraction tool part number number of blades 0- 91047-1 0 9 0- 91047-2 19 0- 91047-3 29 0- 91047-5 20 1-91047-0 10 1-91047-2 35 1-91047-4 12 1-91047-5 14 1-91047-6 15 1-91047-8 0 5 1-91047-9 0 3 2-91047-6 0 6 extraction tools 91047-[ ] 408-7384 11 may 10 rev a locking lance flexible flat cable (ffc) outer edge of connector housing (single-row connector shown) locking lance slot extraction tool (ref) blade
408-7384 2 of 2 rev a figure 3 excessive or improper force may cause damage to the contacts or cable. 4. after the cable and all of the contacts have been completely extracted, remove the tool from the connector. 4. maintenance and inspection to ensure proper operation, the tool should conform to the dimensions provided in figure 4. it is recommended that the tool be inspected immediately when received and at regularly scheduled intervals. it is recommended that the tool be stored in a clean, dry place and cleaned with a soft, lint-free cloth. 5. replacement and repair the tool is not repairable and should be replaced when worn or damaged. additional tools can be purchased from: customer service (038-035) tyco electronics corporation po box 3608 harrisburg pa 17105-3608 6. revision summary revisions to this inst ruction sheet include: ? updated instruction sheet to corporate requirements ? removed obsolete extraction tools ? replaced connector series part numbers with reference part number figure 4 caution ! extraction tool part number dimension part number dimension ab ab 0- 91047-1 20.32 [.800] 21.08 [.830] 1-91047-4 27.94 [1.100] 28.70 [1.130] 0- 91047-2 45.72 [1.800] 46.48 [1.830] 1-91047-5 33.02 [1.300] 33.78 [1.330] 0- 91047-3 71.12 [2.800] 71.88 [2.830] 1-91047-6 35.56 [1.400] 36.32 [1.430] 0- 91047-5 48.26 [1.900] 49.02 [1.930] 1-91047-8 10.16 [.400] 10.92 [.430] 1-91047-0 22.86 [.900] 23.62 [.930] 1-91047-9 5.08 [.200] 5.84 [.230] 1-91047-2 86.36 [3.400] 87.12 [3.430] 2-91047-6 17.78 [.700] 18.54 [.730] tool fully inserted into connector radius between tool blades visible 32.51 [1.280] 2.54 [1.00] 0.76 [.030] b a 6.73 [.265] 0.38 [.015] 2.29 [.09] tool number marked here
|
